877-766-3309 [email protected]

Our Max Defender Paint System brings your home long lasting value.

This limited warranty applies only to Sherwin-Williams’ Max Defender Paint System® coating which is used on Tri County Metals’ painted roofing and siding panels. This warranty is only good for products installed in North America.

1. For THIRTY-FIVE YEARS (35), Sherwin-Williams’ Max Defender Paint System® will not peel, flake, or otherwise lose adhesion to an extent that it is apparent on ordinary outdoor visual observation. Further, failure due to substrate issues including, but not limited to corrosion is not covered by this Limited Warranty.
2. For THIRTY YEARS (30), Roof panels will not change more than five Hunter units when measured per ASTM D 2244 on clean surfaces after removing dirt, other surface deposits and chalk per ASTM D 3964.
3. For THIRTY YEARS (30), Roof panels will not chalk more than a number eight rating when measured per ASTM D 4214, Method A.

Read the warranty details here.

This limited warranty applies only to Sherwin-Williams’ Max Defender Paint System® coating which is used on
Tri County Metals’ painted roofing and siding panels. This warranty is only good for products
installed in North America.

Although it is recognized by Sherwin-Williams and Tri County Metals that most coatings, including Max Defender Paint
System® will fade and change appearance to some degree over a period of time in outdoor installations, and that such
changes may not be uniform between surfaces not equally exposed, Sherwin-Williams warrants that the
Max Defender Paint System® panels covered by this warranty will conform to the performance standards listed below.

SECTION A: LIMITED WARRANTY
1. For THIRTY-FIVE YEARS (35), Sherwin-Williams’ Max Defender Paint System® will not peel, flake, or otherwise lose
adhesion to an extent that it is apparent on ordinary outdoor visual observation. Further, failure due to substrate
issues including, but not limited to corrosion is not covered by this Limited Warranty.
2. For THIRTY YEARS (30), Roof panels will not change more than five Hunter units when measured per ASTM D 2244
on clean surfaces after removing dirt, other surface deposits and chalk per ASTM D 3964.
3. For THIRTY YEARS (30), Roof panels will not chalk more than a number eight rating when measured per ASTM D 4214,
Method A.

SECTION B: REMEDY
If Sherwin-Williams’ Max Defender Paint System® fails to comply with the limited warranty, Sherwin-Williams will pay
for labor and material reasonably necessary to repaint, repair, or replace, at their option, the metal panels exhibiting the
conditions described above or refinish the defective portion of the field installation. The decision whether to replace or
refinish to remedy an honored claim will be made at the sole discretion of Sherwin-Williams. This warranty also applies to
the part(s) being repainted, repaired or replaced, but only for the unexpired portion of the Warranty period applicable to
the original coil coated part. Sherwin-Williams SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL OR
CONSEQUENTIAL DAMAGES, such as, but not limited to, damage or loss of other property or equipment, loss of profits
or revenue, cost of capital, cost of purchase or replacement of other goods, or claims of customers of Purchaser for
business or service interruptions.

SECTION C: LIMITED WARRANTY EXCLUSIONS
This Limited Warranty does not apply to other causes of degradation, including:
1. Failures or damage resulting from under-film or edge corrosion, or failure or defects of the metal
substrate.
2. Max Defender Paint System® that has been stored/installed in such a way that allows contact with animals or animal
waste;
3. Harmful fumes or foreign substances in the atmosphere, or salt spray; or installed on property located 1500 or fewer
feet from salt water environment;
4. Max Defender Paint System® which has been damaged due to moisture entrapment in bundles during transit or
storage or which has been stored or installed in such a way that allows standing water on the coating;
5. Significant differences in insulation below coated metal panel;
6. Where materials/items such as solar panels are attached/adhered to the product.